Bulk and Shop Only

TECH LINE exhaust system coatings are designed to maintain adhesion at temperatures above the normal operating range of an exhaust system. Unless otherwise indicated temperatures given refer to the base metal temperature that a coating can normally be expected to handle. Depending on the resin system, TECH LINE coatings designed for exhaust systems, can handle base metal temperatures in excess of 2000f. Color change can be expected at lower temperatures with many of the coatings. A color change does not necessarily reflect a failure of the coating, as color stability is secondary to the protective function. Several colors have maintained color stability, to base metal temperatures in excess of 1600f. The use of multiple coats including MCS™ can raise the color stability of all exhaust system coatings.

******************
View our Suggested Retail Price List Here

******************

Black Satin™

• SEE RETAIL PACKAGED CATEGORY FOR DESCRIPTION & CHARACTERISTICS
• 4 OZ. (Retail Packaged)
• 12 oz. (Retail Packaged)
• Quart ( Retail Packaged)
• Gallon
• Full cure occurs at 750F
• Especially effective on Turbo housings, head pipe and down tube.
• MCS may be placed under Black satin to impart even greater heat tolerance

   

• Extreme temperature Exhaust system coating designed specifically for Turbo’s.
• Available in BLACK and BLUE
• Reduces under hood temperatures, reduces exhaust manifold surface temperatures
• Improve exhaust gas velocity, increase H.P.
• Available in 8 oz., Quart, (Retail Packaged) , and Gallon
• Air drying requires no baking, full cure occurs at 750F

Cermakrome™ (MCX)

• Ceramic Chrome-Like Coating. (Once Polished)
• Quarts
• Gallons
• Available in a special formulation for low humidity environments (MCXLH)
• CermaKrome Salt Spray Report

ColorGard™

CilGen™ Ceramic based High Heat Coating

• Top coat with CermaSeal™ to give a “shiny” and very hard finish
• Good thermal barrier
• Available in a variety of colors*
• Color stable to metal temperatures in excess of 1400f
• Durable smooth finish
• Good corrosion and chemical resistance
• Will air cure, however curing may be accelerated by curing at 200f. Minimum.
• For air cure, the temperature must be above 65F for a minimum of 8 hours.
  

CERMASEAL™ is a thin film coating designed to insulate and protect Exhaust system coatings. CERMASEAL™ reduces the oxidation that can occur on highly polished Metallic Ceramic coatings, allowing the bright chrome like finish to last much longer. CERMASEAL™ may also be applied to CermaStainless, CermaWhite, Cermakrome and other Tech Line products.

CERMASEAL™ gives a mild gloss to the coated surface and seals the finished part so that it is resistance to moat chemicals found in an automotive environment. CERMASEAL™ provides a smooth surface, which is easy to clean and resists staining from both fuel and oil. CERMASEAL™ may also be applied to any polished metal and some plastic surfaces. CERMASEAL™ requires no baking. CERMASEAL™ is retail packaged, to allow the Coat-It-Yourself enthusiast to take advantage of this new product.

CERMABLUE™ * CERMASSTEEL™

• Metallic Ceramic Coating
• Excellent corrosion protection
• Tested to over 1300f base metal temperatures/1600f Exhaust gas temperatures
• Polishable and provides a variety of colored finishes depending on the polishing time.
  
• Water based with no flammable solvents.
• Can be applied to any metal that can handle the cure temperature, except magnesium
• Available in quarts and gallons
• Requires baking. Cure temperature 500f for 1hour minimum.

Grey Ice™

• Glossy/Metallic gray coating
• Dark charcoal colorGood thermal barrier
• Good corrosion resistance
• High temperature stable
• MCS may be placed under Black satin to impart even greater heat tolerance
• Requires Baking. Cures at 500f. Must be oven cured

CF85™

MCS™, HHBK™ Insulating Coating

PrevCor™ Corrosion Protection Coating

TLHB™ HI HEAT I.D. COATING

Site design by AndComp Technologies www.andcomp.com
Copyright 2000 Tech Line Coatings, Inc.